REAR WHEEL BEARING??
Posted: Fri, 03/20/2009 - 9:04am
Offline
User gallery (1)
REAR WHEEL BEARING??
anyone know where i can get a rear wheel bearing from? thanks in advance, Ben
__________________
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
sentra front bearing if i remember well..
ok thanks a bunch i put it in it works well
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
anyone know if this applies to the front bearings as well? mine are both pretty much shot!
what year sentra are we talkin about here?
http://nissan4u.com/parts/sunny/el_n14/1990_12/type_49/axle_suspension_and_steering/front_axle_and_front_suspension/illustration...
http://nissan4u.com/parts/info/4021050Y00/
http://nissan4u.com/parts/info/4021050Y05/
http://nissan4u.com/parts/sunny/el_n14/1990_12/type_49/axle_suspension_and_steering/rear_axle_and_rear_suspension/illustration_3...
so you guys use a front bearing for the rear?
They are all the same because of the awd. I have replaced all 4 on mine 2 years ago and been perfect.
what year sentra is it ? one of mine needs replacement also. thank you
91-94
are the rear wheel hubs the same as the fronts??
looks like hubs are not according to nissan4u index, they're different front and rear. Same front hub also listed on 100NX = NX2000 NA model
Hub road wheel, front 2 1.476 kg / 3.258 lb
4020250Y00 '90, October — '92, October 92-95 later alternate: 4020250Y10
shares with 100nx=nx2000
Hub rear 2 1.798 kg / 3.969 lb
4320260Y00 '90, October — '92, October 92-95 later alternate: 4320260Y10
nb. front hub number in gtir specs in header has extra digit
Noticed anything "funny" with the exchange rates and parts prices lately:
New Scarier Insider Information: http://www.youtube.com/watch?v=uPg4qTNTP-E
Save Real Money for your Nissan Pulsar Gtir Upgrades!
http://www.canadagtir.com/gallery/user/91gtirgrey/wont-last-long-buy-physical-silver-now
***** "May you live in interesting times."
can anyone confirm if yes or no the 4 bearings are the same or are the front and rear different ?
YES all FOUR BEARINS ARE THE SAME, its the hubs that are different as stated by 91gtirgrey
tyvm
I am hearing this weird noise coming from left side the faster I go ... sounds like a bearing and last time I checked it was getting loose .. anyways my question is ? do I need to buy just the bearing or do I also have to change the hub ? thank you
you can take the hub to a shop and have the old one pressed out and the new one pressed in.. Its usually cheaper in the case of the rear hubs on the GTiR it definitely cheaper!
Mine isn't bigger than yours.. I just like to drive
how can having more work to be done be cheaper ? lol
So when I go to replace my wheel bearings do I also need to replace the inner and outer seals? Is it worth it to buy a bearing removal/installation tool. Sorry for the noob questions... I have quite a bit of experience with cartridge bearings but only with bicycles so my tools only work for much smaller bearings.
Inner seal
Outer seal
Bearing tool
Only Chuck Norris can own a GTi-R. The GTi-R owns everybody else.
you might aswell replace the seals if your doing the bearings. odds are your going to wreck the seals taking them out any ways. i have the same kit aswell works good. when u take the old bearing out save the bearing but take it all apart. then take a grinder to the out side of the outer race to make it sightly smaller than original. you now have a perfect sized bearing pusher for install :) works mint :)
any one got skf replacement bearings. I bought a set a few yes ago and just want to confirm there right.
Mine isn't bigger than yours.. I just like to drive
yep thats what i used
I just recently installed my front wheel bearings and they went in perfect. Bearing tool is really handy, glad I bought it. I used Toyota Celica AWD 90-93 bearings and they are the same. Pretty much just used the bearing number as a reference (can't remember what that was). My question is how do I find the correct inner and outer dust seals. The ones provided don't work for the Pulsar (they were free so no biggie). Will the NX dust shields work? I am changing all 4 bearings so will dust shields be the same for all 4?
Reference numbers for front dust shields are
Inner NOK BD4376E
Outer NOK BD4374E
*edit* looks like they are the same as the NX 2.0 dust covers. Found them on Autopartsway.ca However they are about $8-$10 a piece............ $80 for dust shields? wtf
Only Chuck Norris can own a GTi-R. The GTi-R owns everybody else.
BECK/ARNLEY Part # 0523566 Front Inner CAD$4.52
BECK/ARNLEY Part # 0523679 Front Outer CAD$5.09
RockAuto.com
Score, thanks bro :-)
Only Chuck Norris can own a GTi-R. The GTi-R owns everybody else.
anytime. use this discount for 5% off too: 78396446411137
good until Feb 19, 2012 use as many times as you want.
Have anyone completely dissassemble the rear hub on their pulsar, i am curious to know if the hub dia, height and offset are the same as the fronts