best pistons rods bearings and gaskets for my build??
Posted: Mon, 06/28/2010 - 5:57pm
Offline
User gallery (1)
best pistons rods bearings and gaskets for my build??
hey everyone i was planning on building my engine up and i was wondering if anyone had any input on what parts i should use. the car will have all the mods in my signature, but i figure since it needs a rebuild anyways then i should use some good pistons/rods etc. thanks for the input!
__________________
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
if i was rich http://www.sr20-forum.com/mazworx/31754-mazworx-91-92mm-stroker-kits.html
i am not that serious about it lol
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
ive had good luck with je pistons and eagle rods. idk guess im kinda old school like that. i also know that the brian crower parts/ stroker kit is very nice...but lots of $$$
ok thank you what kind of head gasket, oil pump, timing chain, water pump, and bearings are you running? i was gonna use new pumps and new oem timing chain, what do u think?
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
oem timing chain kit and oem water pump, oil pump (get the whole front cover from nissan), oem gasket set too but I'd get an upgraded headgasket. Bearings - acl bearings either standard or calico coated - make sure they are for the gtir. ARP rod bolts and head bolts. Make sure while you have the lump out that you look at a decent clutch for your power goals too.
RNN14
ok cool thanks i appreciate it
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
i have a toda bottom end in my car and a tomei top end. works great for me so far. revs quick. i also hear good things about hks stuff but dont have any experiance with any hks parts for the pulsar.as far as a headgasket goes my tomei handles everything i throw at it.
caravan where did you buy youre timing chain kit ? I am also planning a rebuild with the things mentionned above.
i havent purchased it yet but they are on ebay so thats prolly where ill get it
13.2 @ 109mph w/ 2.2 60ft //////// garrett 60-1 @18psi, custom Weirtech header, fmic, 720cc injectors, 4" intake, mongoose exhaust, BC coilovers, AEM water/methanol kit, bully stage 4 clutch(highly recommended grips very hard yet engages like a stock clutch!!), and hoping to save up for a straight-cut gearset!!!! Ben
frsport.com has all of the oem gtir stuff you'll need. ericsperformance parts on ebay is another good parts place to get gtir stuff.
RNN14
yes canadian I will be buying most of the stuff on frsport but the timing chain kit dosnt seem to be there... unless I am not looking properly !
things might be cheaper from http://gspec.com/ or eric's performance parts http://stores.shop.ebay.ca/Erics-Performance-Parts__W0QQ_armrsZ1 diff places have cheaper prices for diff things